Go-Kart Split Sprocket: Fitting, Sizes and Gearing

A person riding a go-kart on a race track — Go-Kart Split Sprocket

A go kart split sprocket is a rear axle sprocket made in two halves that bolt together around a hub. Because it wraps around the axle instead of sliding over the end, you can change gearing without removing wheels, hubs, the brake disc or the axle itself. That makes it a favorite with racers who swap ratios between sessions, and a handy fix for DIY builders tired of stripping the rear end. This guide covers how split sprockets work, the chain sizes and tooth counts you will meet, how they compare with one-piece sprockets, how to fit one properly and what to check over time.

What Is a Go Kart Split Sprocket?

A normal one-piece axle sprocket is a solid ring. To change it, you have to remove everything between the sprocket and the end of the axle, or unbolt the axle and slide it out. A split sprocket is cut into two pieces, usually straight across the center, so each half can be placed around the hub and the two bolted together.

The sprocket mounts to a sprocket hub or carrier that is keyed to the axle. The hub stays put; only the sprocket changes. Most split sprockets use the same bolt pattern as solid sprockets for that hub, so you can mix them in your gear box. Our guide to go-kart sprocket hubs explains the hub side of this setup.

Why Racers and Builders Use Split Sprockets

Faster gear changes. At a race track, conditions change through the day. Swapping a split sprocket takes minutes, which matters between practice, qualifying and the final.

No axle removal. On a DIY kart, removing the axle may mean disturbing bearings, brake alignment and hub positions. A split sprocket avoids that.

Emergency repairs. If a tooth breaks or the sprocket bends, a split replacement can be fitted at the track without tearing down the rear end.

The trade-off is a seam. Two halves must be precisely matched and bolted together correctly or the sprocket can run out of true and wear chains faster.

Best Go Kart Sprockets: our top 3 picks

ProductBest forKey featuresPriceBuy
GREHUA 48T Sprocket + Hub KitBest overall #40/41 kit
  • 48T for 40, 41 and 420 chain
  • 1 in bore hub with 1/4 in keyway
  • Key, 4 bolts and nuts included
$34.99as of Nov 17, 2026 3:32 am ESTBuy now →Check current price
YOXUFA #35 60T Sprocket + HubBest #35 chain hub kit
  • 60T for #35 chain
  • 1 in live axle hub, 4-bolt
  • 74 mm bolt circle stated
$31.99as of Nov 17, 2026 11:38 am ESTBuy now →Check current price
Gekufa 60T 8-Hole SprocketBest 60T for bolt-on hubs
  • 60T for 40, 41 and 420 chain
  • 2-1/8 in center bore
  • 8 x 3/8 in mounting holes
$25.49as of Nov 17, 2026 3:32 am ESTBuy now →Check current price

Prices are Amazon’s listed prices as of the date and time shown and are subject to change; the price on Amazon at the time of purchase applies. As an Amazon Associate we earn from qualifying purchases.

See every pick compared: Best Go Kart Sprockets →

Chain Sizes and Tooth Counts

A sprocket has to match the chain. In karting, two families dominate:

  • #219 chain. A narrow, light chain common on two-stroke sprint karts. Split sprockets for #219 are widely available, usually in aluminum.
  • #35 chain. Common on four-stroke racing karts and many DIY builds. Split #35 sprockets are also common.
  • #40 and #41 chain. Used on heavier utility karts and some off-road builds. Split sprockets exist but are less common; one-piece steel sprockets dominate.

Tooth counts vary widely, from the 50s to the 80s and beyond on racing karts, depending on engine, track and tire. More teeth on the rear sprocket gives more acceleration and lower top speed; fewer teeth gives the reverse. Our main go-kart sprockets guide covers gearing principles, and the go-kart sprocket calculator guide shows how to work out ratios and speeds.

Split vs One-Piece Sprockets Compared

Feature Split Sprocket One-Piece Sprocket
Change without removing axle Yes No, usually
Typical material Aluminum, some steel Aluminum or steel
Runout risk Higher if halves misalign Lower
Best use Race karts and frequent gear changes Utility karts and set-and-forget builds
Typical price About $20 to $60 About $10 to $50

Aluminum sprockets are light and easy on chains but wear faster. Steel lasts longer and suits higher-torque or dirty off-road use. Many racers run aluminum split sprockets and replace them often.

How to Choose a Go Kart Split Sprocket

Match the chain pitch. A #219 sprocket will not run a #35 chain. Confirm the chain size printed on your chain plates or in your kart’s manual.

Match the hub bolt pattern. Sprocket hubs use different bolt circles and hole counts. Measure your hub or check the manufacturer’s spec before ordering.

Choose the tooth count. Start from a known baseline for your engine and track type, often available from your engine builder or local club, then adjust in small steps.

Pick the material. Aluminum for racing and light chains; steel for longevity and heavier karts.

Buy matched halves. Halves are machined together. Never mix halves from different sprockets, even of the same tooth count.

Fitting a Split Sprocket

Raise the rear of the kart, loosen the engine mount and slacken the chain. Remove the old sprocket bolts and take off the old sprocket.

Place the two halves of the new sprocket around the hub, matching any alignment marks or pins. Insert the bolts and tighten them in a crisscross pattern gradually, so the halves draw together evenly. Torque to the hub or sprocket maker’s value and use thread locker if specified. Some split sprockets include small dowels or tabs at the seam; make sure these seat fully.

Spin the axle and watch the sprocket against a fixed reference, such as a pointer or a straightedge. It should run true without side-to-side wobble or up-and-down movement at the seam. Then check chain alignment with the engine sprocket using a straightedge, set chain tension, and tighten the engine mount. Our go-kart clutch chain guide covers chain tension and alignment checks.

If you change tooth count, the chain length may need to change too. Add or remove links, or move the engine on its mount, to keep proper tension.

Inspection and Wear

Check sprocket teeth regularly. Worn teeth look hooked or pointed, like waves breaking in one direction. A worn sprocket wears chains quickly and can throw a chain under load. On split sprockets, also check the seam: if the halves have shifted or the bolts have loosened, the teeth at the joint will show uneven wear.

Replace chains and sprockets together when both are worn; a new chain on a worn sprocket, or the reverse, wears out quickly. Keep a log of tooth counts and track conditions so you can repeat good setups.

Split Sprockets on DIY and Utility Karts

Split sprockets are mostly associated with racing, but they can help on home-built karts too. If your rear axle carries a brake drum, wheel hubs and bearing collars that all have to come off to reach the sprocket, a split design turns a one-hour job into a fifteen-minute one. The key requirement is a sprocket hub with a bolt-on flange rather than a sprocket welded to the axle or pressed onto a keyed bore.

Utility karts with #40 or #41 chain and a torque converter usually run heavier steel sprockets, and split versions are harder to find in those sizes. In that case, a bolt-on hub with a one-piece sprocket is still easier to service than a welded sprocket, even if the axle end must be cleared. Whatever the setup, keep a spare sprocket and the correct bolts in your toolbox so a damaged sprocket does not end the day.

Common Mistakes

  • Mixing halves from different sprockets.
  • Tightening one bolt fully before the others, which can pull the halves out of line.
  • Forgetting to recheck chain tension after changing tooth count.
  • Skipping a runout check after fitting.
  • Using a sprocket designed for a different hub bolt pattern with oversized washers to make it fit.

Safety Notes

A sprocket that comes loose or a chain that derails can lock the rear wheels or whip the chain toward the driver. Use chain guards where your kart or class requires them, recheck sprocket bolts after the first session, and never run a sprocket with cracked or broken teeth. Racing classes may limit gearing or materials; check the current rulebook from your sanctioning body.

Pros and Cons

Split sprockets are a practical upgrade for anyone who changes gearing often.

Pros

  • Change gearing without removing wheels or axle
  • Quick to swap at the track
  • Fit standard sprocket hubs for most racing chassis
  • Light aluminum options available

Cons

  • Halves can misalign and cause runout
  • Aluminum versions wear faster than steel
  • Less common for heavy #40 and #41 utility setups
  • Slightly more expensive than one-piece sprockets

Frequently Asked Questions

What is a split sprocket on a go-kart?
It is a rear axle sprocket made in two halves that bolt together around the sprocket hub, so it can be changed without removing the axle or wheels.

Are split sprockets as strong as solid ones?
Quality split sprockets that are fitted correctly are strong enough for racing. Their weak point is the seam, so even bolt tightening and runout checks matter.

Can I use a split sprocket on any go-kart?
You need a sprocket hub with a matching bolt pattern and a sprocket that matches your chain size. Most racing chassis and many DIY hubs accept them.

Do I need to change the chain when I change sprocket size?
Often you need to adjust chain length by adding or removing links, or move the engine to restore tension. A large change in tooth count usually requires a different chain length.

What chain size do split sprockets use?
They are most common for #219 and #35 chain. Split sprockets for #40 and #41 chain exist but are less widely stocked.

How often should I replace a split sprocket?
Replace it when teeth look hooked or pointed, when the seam shows uneven wear, or when you replace a worn chain.

Final Thoughts

A go kart split sprocket saves time every time you change gearing, and it makes trackside repairs far easier. Buy matched halves for your chain and hub, tighten them evenly, and check runout and chain alignment after every change. For complete gearing setups, see our guide to go-kart sprocket kits.